SOLCRY®
Home / Articles / Titanate Yellow P.Br 24 in Automotive Coil Coati

Titanate Yellow P.Br 24 in Automotive Coil Coatings: Meeting 10-Year Florida Exposure Standards

Quick answerYELLOW 3124 (P.Br 24 chrome antimony titanium brown rutile, CAS 68186-90-3) dispersed at 15% PVC in 70% PVDF and in polyester coil coatings held ΔE*ab 1.3 and 2.8 respectively after ten years at 45 degrees south in South Florida, with gloss retention above 85% in both systems.

Coil coating is a ten-year bet

A coil-coated aluminium panel on a building facade is a ten-year bet made in a factory. The coating is applied, cured and wound at line speed, then installed on a building where it cannot easily be repainted. The architectural specification that governs it, AAMA 2605 for the most demanding PVDF systems, sets a minimum color-retention requirement over ten years, and South Florida at 45 degrees south is the standard exposure site used to prove it.

That exposure is deliberately brutal: high ultraviolet dose, year-round heat and humidity, salt from the coast and regular rain. A pigment that survives it can be specified anywhere. A pigment that fades there will fade on the building, and the cost of the failure falls on the coater rather than on the pigment supplier, which is why coil coaters are conservative about colour chemistry.

The pigment: Y3124 at P.Br 24

YELLOW 3124 is a chrome antimony titanium brown rutile, classified as Pigment Brown 24 at CAS 68186-90-3. It is a rutile pigment: the tetragonal TiO2 host is doped with chromium and antimony, and the colour comes from the charge-transfer and ligand-field behaviour of those ions in the rutile lattice. The result is a warm, brown-shade yellow with the opacity and tinting strength that a rutile host provides.

For a coil coating, those optical properties matter as much as the durability. A pigment that delivers hiding power at a lower loading lets the formulator reduce film thickness or pigment volume concentration without the substrate showing through. The durability side is equally direct: 800 °C heat resistance by CF-33, grade 8 light fastness, 30+ years of weathering and pH 1-14 chemical resistance, all from the same rutile crystal.

PVDF versus polyester: the measured numbers

In the study, YELLOW 3124 was dispersed at 15% PVC in both a 70% PVDF formulation and a polyester formulation, applied to chromated aluminium and exposed at 45 degrees south in South Florida. After ten years of direct weathering, the PVDF system showed ΔE*ab of 1.3, well inside the AAMA 2605 limit. The polyester system showed ΔE*ab of 2.8, still acceptable for AAMA 2604 classification.

Gloss retention exceeded 85% in both systems, with no evidence of chalking or pigment surface degradation under scanning electron microscopy. The gap between the two binders is the interesting part of the result: the pigment performed identically in both, and the difference in colour change came from the polymer's own UV stability. That is what a stable pigment should look like in a test - it stops being the variable.

Why a rutile titanate handles ultraviolet

The rutile host is a wide-band-gap oxide, and the colouring ions sit inside that lattice rather than on its surface. There is no organic chromophore to be attacked by ultraviolet photons and no dye that can migrate into the binder. The pigment absorbs where its dopant ions absorb and scatters the rest, and the crystal that does this is the same crystal after a decade of exposure.

That is also why the pigment does not chalk. Chalking is a surface phenomenon in which the binder degrades and releases pigment particles, leaving a powdery layer that scatters light and lightens the colour. A pigment that is inert to UV does not accelerate that process, and a rutile host that is already fully oxidized has nothing left to react with.

A specification checklist for coil coaters

Specify the pigment by C.I. name, CAS number and crystal form: P.Br 24, CAS 68186-90-3, rutile. Require a certificate of analysis with the heat resistance result by CF-33 and the light fastness grade, and ask for South Florida or equivalent xenon-arc weathering data on the pigment itself rather than assuming the binder will carry it. Confirm the chemical resistance across pH 1-14 if the facade will see acid rain or cleaning agents.

Then run the coating trial at the film thickness and PVC you will use in production. The ten-year result above came from a specific formulation at a specific loading, and the value of the data is that it proves the pigment is not the weak link. Reproducing that in a new formulation starts with keeping the pigment identity fixed while everything else is optimized.