Cobalt Chromite GREEN 3603 in Concrete Masonry: Permanent Color Without Carbonation Fading
Concrete is a hostile matrix for colour
Concrete coloring presents a combination of stresses that no other building material reproduces. Fresh concrete is strongly alkaline, with a pore solution around pH 12-13. It carbonates over time as carbon dioxide diffuses in and reacts with calcium hydroxide, which slowly lowers the pH and changes the chemistry at the pigment surface. It is exposed to ultraviolet light, to rain, and to the soluble salts that produce efflorescence at the surface.
A pigment in concrete therefore has to be stable in a high-pH environment, stable as that environment changes, and stable under UV at the same time. Most organic pigments fail one or more of those tests. The failure is not usually a dramatic colour loss; it is a gradual shift and fading that becomes obvious after a few seasons, when the coloured element no longer matches the rest of the building.
Why organic greens fail in two to three years
Organic pigments are built from conjugated molecular structures, and those structures are exactly what alkalis and ultraviolet light attack. In a high-pH pore solution, ester and amide groups hydrolyse; under UV, the conjugated system is oxidized. In a coating the pigment is protected by the binder, but in concrete the pigment is dispersed directly in the cement matrix with only a thin layer of material between it and the pore solution.
The result is that organic greens in concrete typically fail within two to three years under these combined stresses. The colour fades, shifts or becomes patchy, and there is no maintenance route: a coloured concrete paver cannot be repainted economically. That is why permanent colour in cementitious construction is a pigment-chemistry decision made at the batch plant, not a cosmetic choice made at the end.
Spinel inertness at pH 12-13
GREEN 3603 is a cobalt chromite green spinel of the P.G 36 family, and the spinel lattice is chemically inert to the cement matrix. The colour comes from cobalt and chromium ions held in a cubic close-packed oxide, with no hydrolysable groups and no organic structure. The high pH of fresh concrete has nothing to attack, and the pH drop caused by carbonation has nothing to reverse.
That inertness is the same property that gives the whole CICP range its pH 1-14 chemical resistance. It is worth noting what that range means here: the pigment is stable at the alkaline end where concrete lives and at the acidic end where acid rain or cleaning agents sit, with no gap in between. The spinel also carries the standard durability envelope - 800 °C by CF-33, grade 8 light fastness and 30+ years of weathering - although in a concrete paver the alkali resistance is the property that decides the outcome.
Field data: twenty installations, ten years
Field data from twenty installations - paving blocks, roof tiles and architectural precast panels - confirms zero color shift after more than ten years of service across diverse European climates. The installations cover the range of exposure a concrete element can see: horizontal surfaces that hold water, vertical facades that take driving rain, and roof tiles that see the full ultraviolet dose at a shallow angle.
Zero shift is a strong result, and it is worth being precise about what it means. It means the measured colour difference stayed below the level at which the eye can detect a change on the installed element. It does not mean the concrete itself was unchanged - concrete always changes, as efflorescence blooms and washes away and the surface slowly weathers - but the pigment's contribution to that change was not detectable.
Specifying permanent green in cementitious systems
Specify the C.I. name and the crystal form rather than a shade reference: a cobalt chromite green spinel, with the P.G 36 family named on the TDS, and the grade code confirmed against the batch certificate of analysis. Where the project has a colour-hold requirement, ask for the field or accelerated weathering evidence that supports it, and check that the evidence is for a cementitious application rather than for a coating.
Then control the things that actually change concrete colour: the cement source, the water-to-cement ratio, the curing regime and the pigment dispersion in the mix. A stable pigment removes one variable from that list. It does not remove the others, and a batching plant that controls all of them gets a coloured element that still matches its original sample a decade later.